The equipment is used for scraper cleaning of printing press, such as residual solder paste, dust cleaning. The "scraper cleaning machine" uses the scraper to rotate in the rotating basket and is cleaned by high pressure spray, ultrasonic cleaning, rolling rinsing, large flow fan hot air drying and other technologies to ensure the cleaning effect. The use of alcohol liquids is prohibited. If the user uses alcohol liquids without permission and causes safety accidents, the manufacturer has nothing to do with it. Scope of application(Printing scraper) One-button operation, the whole cleaning process is fully automatic, automatic adding and discharging of washing liquid without manual intervention. Equipment low energy consumption, low noise, no pollution, energy saving and environmental protection, the whole stainless steel structure, small footprint. The open state of the machine cover has protection function and cannot be started. All the outlet of the liquid tank is equipped with a filter screen to prevent impurities from entering and protect the pump. Cleaning, rinsing, air cutting, drying function in one. The time and speed of adding and discharging liquid, cleaning and rinsing can be set through the man-machine interface. Imported PPH pipeline maintenance is simple Solder paste recovery device The nozzle pressure can be monitored during the cleaning process to ensure the cleaning effect. Model YSL-680 Size of equipment 1400*900*1300 Working basket diameter 200mm Maximum length of scraper 600mm Work basket load 20KG Gas pressure range 0.4-0.6Mpa Tank capacity 60L Pressure of spray 0.15-0.3Mpa Maximum power 18KW Voltage/frequency 380V/50HZ Recommended cleaning agent Water based cleaning agentYSL-6001 Cleaning: The cleaning process usually uses water - based cleaning solution, which is added externally. The liquid must be heated by a heater prior to cleaning operations to enhance cleaning capacity. Set the cleaning time on the touch screen. During cleaning, the high pressure water flow generated by the water pump is used to peel all the residual solder paste on the scraper to achieve the purpose of chemical cleaning. The peeled solder paste is filtered out through the bag filter device for recycling, so that the cleaning liquid recycling, while extending the life cycle of the cleaning liquid. Make the cleaning part dry without residue. The permanent combination of pollutants will not lead to the gradual reduction of the effective ingredients in the solution and shorten the service life, safe and reliable after cleaning. Rinsing: The rinsing process uses water as the rinsing solution, which is added from an external pipe. Set the rinse time on the touch screen. When rinsing, the pressure produced by the water pump is used to shock the liquid residual substance off the fixture surface. The stripped pollutants are filtered out through the filter device to avoid secondary pollution and ensure the cleaning effect. Drying: The drying process is to dry a small amount of water and water gas taken out by the scraper from the rinsing tank by using the high temperature and circulating hot air generated by the heater. In the process of wind flow, the heater will heat the wind quickly. When the hot air blows to the fixture surface, the circulating hot air speeds up the evaporation of the liquid. Remove moisture and moisture from the tool, thus achieving the purpose of drying. Advantage: 1. Automatic filling and draining, rinsing function Compared with similar products of other brands, the equipment has added automatic drainage system, rinsing function, so that the operator is more simple and convenient. 2. Tin paste recovery As there is too much solder paste on the scraper, a washable stainless steel bag filter is specially designed to recover solder paste. Compared with the traditional disposable filter element, it greatly reduces the cost of consumables. 3. Pipe material Imported PPH pipe material, using hot melt welding, can resist strong acid and alkali, to ensure the long-term use of no leakage. Relative to the stainless steel pipe maintenance, maintenance, replacement, more convenient and simple. Return on investment 1. Save labor 2. The service life of the scraper is extended 3. Environmental protection and pollution-free, prevent chemical damage to the human body 1. How many scrapers can you fit? Scraper size (mm) : 250-600 Display quantity (handfuls) : 6 2. How long does it take? According to the different curing degree of the solder paste of the scraper, the cleaning time will be different. The following empirical data can be used for reference: Cleaning time (Theoretical setting time) Time of spray 1-3min Ultrasonic cleaning time 3-8min Second spray time 2-5min Rinse time 1-3min Drying time 3-7min
MORE>
Equipment overview: for the electronic industry SMT steel mesh, copper mesh, wire mesh, microporous mesh and crystal disk and other types of screen cleaning; The equipment completely uses compressed air as energy, does not use electricity, does not exist any fire hazard, adopts the humanized design, one-button operation, easy to complete the cleaning, drying work; Is a high performance pneumatic automatic cleaning equipment from cleaning to drying process, using air pressure automatic operation; The cleaning fluid is recycled, low loss; Application field Cleaning object Cleaning process cycle diagram Schematic diagram of the principle of steel net drying 1.Side wall intake blow dry 2.Separate air and liquid passages Product structure and function Suitable for steel mesh size L750 × W750 × H40(mm) 【Extra large size to order】 Overall dimensions L1000*W700*H1730(mm) Maximum volume of tank 50L Optimum liquid usage 40L Cleaning method 360°Rotary double side isobaric injection High pressure injection (cleaning + blow drying) Cleaning time 2-4min The drying time 2-5min An external gas source 0.4～ 0.6 (Mpa) Gas consumption 400 ～600( L/Min) Exhaust port size Φ125×H25(mm) Filtration system (Level 1) Primary filter element filtration: 10 µM (to filter impurities and labels) Filtration System (Level 2) Secondary filter element filtration: 5 parts (to filter solder paste and rosin particles) Filtration system (level 3) Three-stage filter element filtration: 1 rod (to filter solder paste and rosin particles) Machine weight 240KG Related parameters of the three-stage filter system Project Filter Brand Filter element replacement cycle Level 1 10μm Impurities/Labels HDX 12 Months Level 2 5μm Tin ball/rosin pellet HDX 1～2 Months Level 3 1μm Solder paste/rosin particles HDX 1～2 Months Project Parameter Cleaning fluid Alcohols, water - based solvents are suitable Applicable to screen size ≤A 29-inch screen can be cleaned Cleaning time 3-5 minutes The drying time 3-5 minutes Consumption of cleaning fluid 120ml/Pcs The product features 1. All stainless steel body: beautiful, wear resistance, corrosion resistance, in line with environmental requirements and standards; 2. Full pneumatic operation, no electricity, no fire and other safety hazards; 3. Side wall inlet and blow-drying design; 4. Humanized design: one-click operation and automatic draining function, the operation is very simple; 5. Replaceable modular controller and quick plug design, maintenance is also very simple and convenient; 6. Two-stage filtration system, low exhaust outlet and S-type exhaust pipe design: solvent circulation, low liquid consumption; 7. High density isobaric bilateral rotating cleaning nozzle, strong cleaning force, does not destroy the tension of steel mesh. 8. Systematic integration of global quality control devices, to ensure good quality, stable performance, long service life; Maintenance and Maintenance Replaceable modular controller and quick plug design, easy and convenient maintenance 1.Automatic filling and draining 2.Controller Maintenance Replace the filter element: 1. Open the bin door at the lower right of the device, remove the filter cartridge with a wrench and take out the built-in old filter element, and install the new filter element after cleaning. Note: When replacing the filter element, it is necessary to wear industrial rubber gloves to drain the liquid in all pipes, liquid storage tanks and filters inside the equipment. So as not to pollute the newly replaced filter element, and not to achieve a good filtration effect. 2. Use a special wrench to open it 3. Remove the filter cartridge clockwise to tighten and counterclockwise to loosen. After replacing the new filter element, install and tighten it. Then start the machine and check the filter for liquid leakage. If yes, tighten it again until there is no leakage Tank cleaning 1. Clean the filter box and replace the filter screen 2. Open the bin door at the lower right of the device and unscrew the cover of the liquid storage tank. There is a filter inside the liquid storage tank. Remove the filter bag, clean the filter bag inside and the debris at the bottom with the cleaning solution (when changing different cleaning solution, take out the filter bag, take out the filter bag and rinse it with water before use), and then put it back in the original position. Finally, install the liquid storage tank cover and close the door. As shown in figure: Clean the instance Comparison of Cleaning Examples
MORE>
Device overview 1. For the surface cleaning of SMT PCB and PCBA boards in the electronics industry, the most advanced cleaning process in the industry is used to achieve 100% cleanliness and environmental protection. 2. The machine consists of cleaning system, rinsing system, fine rinsing, drying system and filtering system. 3. The equipment uses water-based liquid cleaning agent and DI water for rinsing, without any safety hazard, and no harm to personnel. Cleaning objects: PCBA Flux Cleaning Passive Components Flux Cleaning Semicon Flux Cleaning Main structural components: The equipment is mainly composed of rack, spray cleaning system, spray rinsing system, fine rinsing system, cleaning basket moving mechanism, cleaning liquid tank, rinsing liquid tank, electric heating air system, water circulation system, spray room, hot air drying system, The electrical control box is composed. Working diagram: a. The heating systems of the cleaning liquid tank, the fine rinsing liquid tank and the initial rinsing liquid tank are independently controlled. b. Waste water is generated by overflow, which greatly saves water consumption. Cleaning, fine rinsing, initial rinsing, equipped with independent pump, independent control, to eliminate the phenomenon of liquid channeling. The chemical isolation ensures the cleanliness of the rinse water and improves the cleaning quality of the product. Introduction of Nozzle and Boom Structure Adjustable nozzle pressure: 30~90PSI Number of spray rods: 4 (fixed) Schematic diagram of the upper spray boom Schematic diagram of the middle boom 1 in the middle (360°rotation) and 4 in the bottom (fixed); 9 in total Number of nozzles: 98 refer to the diagram on the right Advantages: to achieve all-round spray cleaning of PCBA without dead angle, which is superior to the traditional design of 360° rotating spray bars in the upper middle and lower parts. Schematic diagram of the lower boom Technical Specifications Machine dimensions (mm):L1670*W1100*H1860 Voltage:Three-phase 380V (three-phase five-wire) Total power:33KW Rated current:50A Gas source:0.4-0.6Mpa Exhaust vent:Ø125 Cleaning tank volume:42L Initial rinse tank volume:28L Fine rinse tank volume:55L Filter element:0.2μm Basket size:500MM*550*100MM (upper and lower layers) Cleaning time:8-10Min can be set Cleaning method:Spray cleaning-spray initial rinsing-spray fine rinsing-wind drying Operation control:PLC+touch screen (one key start) Feature of product 1. A high-pressure spray system specially used for water-based cleaning solutions to clean PCB/PCBA and other processes. 2. Three-liquid tank, equipped with heating system, to meet the needs of cleaning, initial rinsing, fine rinsing and hot air drying. 3. Process flow: cleaning - chemical isolation - rinsing (open loop/closed loop) - drying. 4. Prepare advanced automatic touch screen operation software, save program files, use and simplify. 5. The system counting function can automatically accumulate the number of cleaning PCB boards and the number of circulating filtration times. 6. The liquid and pump pressure can be displayed through the panel pressure gauge, which can timely feedback the operation status of the equipment. 7. The cleaning pressure can be adjusted independently, with a visual window, and the pressure can be adjusted according to the cleaning requirements of the PCB board. 8. The conductivity monitors the rinsing solution to ensure cleanliness, and the conductivity can be set to meet the process requirements of different PCB boards. 9. The overall stainless steel body is sturdy and durable, resistant to acid, alkaline and other cleaning fluids. 10. The overflow method is adopted for rinsing, and the fine rinsing water overflows to the initial rinsing box, and there will be no repeated pollution. 11. High-pressure fan + hot air drying, the drying effect is faster and more thorough. 12. Lower operating cost, only 80-120ml of liquid is needed for each cleaning, and the residual liquid is directly recovered by the pipeline and pump after cleaning, which can reduce the consumption of liquid by 50%. Comparison of cleaning examples Before cleaning After cleaning Before cleaning After cleaning
MORE>
Device overview YSL-660 series automatic PCBA board cleaning machine; is an on-line automatic PCBA board special cleaning machine, suitable for traditional board washing water, without manual contact with cleaning agent, the equipment combines PCBA board transmission technology with brush cleaning technology Combined, multiple brushes in all directions, front, back, left and right, cleaning without dead ends, to ensure that the PCBA board meets the cleanliness requirements. It is suitable for cleaning the welding surface of single-sided PCBA board, and will not wet the front components. Machine Features 1. The machine has a unique body structure, stable performance and the highest cleaning effect in the industry. 2. It is specially used for the cleaning of tin beads, flux traces and scratches. 3. Imported brown brush, anti-static brush, will not generate static electricity and will not hurt the PCBA board. 4. It is suitable for PCB boards with board edges, (the board edge distance is at least 1.5mm), and the PCBA board adapts to the width range. 5. Thickened shrapnel claw ensures that the PCBA board will not shift during transportation. 6. Cleaning agent automatic coating system: ensure that the welding surface of the PCBA board can be evenly coated with washing water without affecting the surface of other parts. 7. Disc brush + two rollers: ensure that the PCBA board is cleaned in place in all directions without dead ends. 8. The cleaning brush height and speed (stepless speed change) can be adjusted to adapt to different levels of cleaning needs. 9. The waste generated by the work is automatically gathered in the filter box at the lower part of the machine, which is convenient for cleaning. 10. Driven by high-quality electronic speed-regulating motor, the motor speed is steplessly adjustable and durable. 11. Powered by 220 volts. Easy to use. 12. Adopt brand electrical appliances and control system to ensure the reliability and stability of the control system. 13. Adopt modular control. PCB/PCBA Structure and function 1. Equipment structure: including feeding and connecting mechanism, transportation mechanism, brush cleaning system, circulating filter system, air drying system, PLC program controller, and other automatic control systems. Each system is an independent modular design, easy to operate and easy to maintain. 2. The whole machine is automatically controlled by PLC, with complete functions and two operating modes, automatic and manual. The automatic mode (economy operation mode) can significantly reduce the consumption of cleaning agent and electric energy. 3. The disc brush and the roller brush simultaneously clean the bottom of the PCB A board in all directions, front, back, left and right, and there is no dead angle for cleaning; 4. Cleaning module Equipped with a completely closed three-stage automatic circulation filtration system, which continuously filters and cleans the stains, so that the cleaning liquid is always maintained at a high level of activity, and the cleaning liquid is recycled. 5. The cleaning liquid tank is equipped with low liquid level alarm and over-limit liquid level alarm functions. 6. The air-drying device acts on the cleaned PCB A board through the fan to make the surface dry quickly. 7. The motors of the wet cleaning module and the dry cleaning module are independent, and the speed can be adjusted independently. The height can be adjusted independently. Model YSL-660 YSL-660N Maximum size of PCBA board: 350mm(L) x 350mm(W) 550mm(L) x550mm(W) External dimensions: L1880*W870*H980±2mm L2150*W970*H980±2mm Coating Roller Size: φ100mm φ100mm Disc brush size: φ350mm φ550mm Spindle speed: 0-500 rpm (adjustable) 0-500 rpm (adjustable) Operating Voltage: 220V/50HZ 220V/50HZ Total power: 1(KW) 2.2(KW) Transmission speed: 0.05～1.8m/min(stepless speed change) 0.05～1.8m/min(stepless speed change) Structure and function Primary Wet Cleaning Module It consists of two sets of abrasive brushes and two sets of spray pipes. The PCB board is brushed by reverse rotation, and the cleaning liquid is returned to the circulation system. Secondary dry cleaning module Contains a set of disc brown brushes that rotate in reverse to clean the PCBA board. Three-stage wet cleaning module It consists of a set of roller abrasive brushes and a set of spray pipelines. The PCBA board is brushed by reverse rotation, and the cleaning liquid is returned to the circulation system. Four-stage dry cleaning module Contains a set of disc brown brushes that rotate in a positive direction to clean the PCBA board. Machine structure and features 1.Touch screen control, the machine has the function of automatically adding and draining liquid medicine, and displaying the liquid level in real time 2.Liquid level control system: When the liquid level in the liquid storage tank drops to the low level warning line, the liquid level controller will send an alarm signal to prompt manual replenishment. 3.Imported anti-static brushes are used, which are wear-resistant, have a long service life and reduce maintenance costs. 4.Precise induction, more energy-saving and efficient, and reduce the cost of use. 5.Independent air outlets on both sides will not cause environmental pollution, more environmentally friendly and adjustable. Cleaning agent circulation system 1. Cleaning tank 2. Liquid storage tank 3. Primary filter 4. Sedimentation tank 5. Reservoir 6. Circulating pump Control System Manual operation mode Each system function can be completed manually one by one Fully automatic operation mode 1. When there is no PCBA board in the machine, the system will judge. At this time, the brush will be cleaned and the water pump will enter the stop state. 2. The cleaning fluid circulation system enters a fully closed state cleaning process Project Craft name Cleaning introduction Cleaning speed Cleaning method Cleaning box Note 1 Primary cleaning Wet Type Adjustable Roller brush (black) Custom made Anti-static material 2 Secondary dry cleaning Dry type Adjustable Disc Brush (Black) Custom made Anti-static material 3 Three-stage cleaning Wet Type Adjustable Roller brush (black) Custom made Anti-static material 4 Level 4 Dry Cleaning Dry type Adjustable Disc Brush (Black) Custom made Anti-static material
MORE>
Precision laser cutting dust removal Applicable working conditions Mainly used for the collection and treatment of floating and suspended dust with a large amount of dust, and small central dust collection systems for multi-station operations; suitable for grinding, cutting, stirring, sandblasting, ceramics, paper, steel, food, plastic, Wood processing and other industries; Product Features 1. Large air volume and low noise, industrial fans can work continuously for 24 hours; 2.4 automatic pulse cleaning systems for PTFE-coated filter cartridges; 3. It can be matched with small laser cutting machines for dust removal; engraving machines, grinders/belt machines, rubber cutting machines, grinders, milling machines and other machining equipment are matched with dust removal. It is mostly used for the collection and treatment of floating and suspended dust. 4.2.0 sheet metal, independent electrical box, built-in air duct 5. Separate dust collecting bucket with see-through window, you only need to lift and pull the dust collecting bucket to pull out the dust collecting bucket. There is a universal wheel under the dust collecting bucket, which is very convenient for dumping and inhaling materials. 6.68DB noise reduction technology can be placed indoors and outdoors to keep front-line employees away from noise hazards. Specification Unit YSL-370 YSL-550 Power Kw 3.7 5.5 Voltage V 380V 50Hz/60Hz Capacity L 50 50 Total filter area ㎡ 32 32 Filter composite EA 4 4 Filtration accuracy μm 0.3 0.3 Air flow volume m³/H 2900 3200 Vacuum suction Kpa -3.8 -4.2 Noise Db 67 68 Air pressure Mpa 0.5Mpa＜work value＜0.6Mpa Size MM 900*850*2250 Cleaning method Pulse automatic jet cleaning
MORE>
Applicable working conditions Robot welding, automation equipment, automatic assembly line, PCB, precision laser engraving, precision laser cutting and other supporting vacuuming. Feature of product 1. Linkage interface design, which can be linked with supporting equipment. 2. It can work continuously for 24 hours. 3. The product has phase sequence and thermal overload protection functions. 4. Schneider brand electrical appliances, with the characteristics of safety and stability. 5. Equipped with 2 PTFE-coated high-efficiency filters as standard, with a filtration area of 2.16m² and a filtration accuracy of 0.3μm. 6. Pulse cleaning, automatic pulse cleaning filter time can be set according to requirements. 7. The pull-out large-capacity dust-collecting drawer is convenient for dumping garbage. 8. The machine body is made of 2.0 thick sheet metal, and after spraying and high temperature baking, the paint will not fall off and rust. 9. With brake universal wheel, it is convenient for the machine to move. Product parameters Unit YSL-200P YSL-300P power Kw 2.2 3 Voltage V-Hz 380-50/60 380-50/60 capacity L 15 15 total filter area c㎡ 21600 21600 Filtration accuracy μm 0.3 0.3 number of filters PC 2 2 air flow volume m³/h 320 320 vacuum suction mbar 190 260 noise dB 66 67 Suction diameter mm 40/50 40/50 Power cord length m 7 7 Net size (L*W*H) mm 530*500*1030 530*500*1030 Filter cleaning method - Pulse cleaning sobbing dust drawer cooling fan Water separator 2 filters area 2.16㎡ Schneider Electric Control panel/negative pressure gauge 1. Remote control terminal Step 1 Insert the remote control terminal plug into the remote control terminal socket 2. Power indicator panel The second step is to turn on the power switch and the local/remote switch 3. Remote control switch Step 3 After the installation of the remote control switch is completed, turn on the switch, that is, the switch signal contacts, and the machine can be turned on remotely.
MORE>
Suzhou cutting fume dust collector is suitable for laser cutting fume dust removal, grinding and polishing dust removal, and grinding machine grinding and dust removal. Technical Specifications Unit YSL-370L Voltage V 380 capacity L 30 power KW 3.7 flow m³/H 3200 noise Db 71 vacuum suction Kpa 3.8 filter area ㎡ 32 Filtration accuracy Um 0.3 number of filters EA 4 control panel Cartridge filter sobbing dust drawer Built-in pulse injection system Pulse control system Water separator
MORE>
Lithium battery winder dust collector is a cabinet type dust collector, also called winder dust collector. Some customers of winder dust collector also call it lithium battery filter cartridge dust collector. Applicable working conditions Winding machine dust removal, lithium battery industry dust removal, grinding and polishing workshop dust removal feature of product 1. Modular design of dust collector for lithium battery winding machine, the top is the motor and control system, and the bottom is the garbage filtering and collection system. Modular design machine with low noise. 2. The machine is equipped with an industrial dust removal fan, which has the advantages of large air volume, low noise and stable performance; 3. The machine is equipped with a remote control port as standard, and the local/remote control switch can be replaced at will according to the needs; 4. The inside of the dust collector of the lithium battery winding machine adopts multiple dust-proof designs. After the dust is inhaled, a cyclone airflow is formed, which speeds up the dust-removing speed, reduces the dust, and reduces the burden on the filter; 5. The power, air volume, suction port, and pipe diameter of the small industrial dust removal equipment can be customized according to the needs of customers. Customers can choose the position of the suction port and install the suction port on both sides of the movable suction arm according to the on-site working conditions. The suction port can be selected according to the on-site working conditions Location and installation of movable suction arm, the machine can be equipped with an explosion relief valve at the idle suction port; 6. The machine has phase, phase sequence and overload protection functions; 7. Built-in automatic pulse cleaning system, which can set the pulse cleaning time interval according to different working conditions, can automatically clean the dust attached to the cartridge filter, reduce the frequency of filter replacement, and maintain normal suction; 8. The dust collector of the lithium battery winding machine is equipped with 2 barrel-type PTFE-coated HEPA cartridge filters, with a filtration area of 16 square meters and a filterable dust diameter of 0.3 μm. The rotary card installation method of the filter does not require tools; 9. The oil-water separator of small industrial dust removal equipment can filter the impurities in the compressed air and protect the pulse system. 10. External separate 30L capacity dust collector is convenient for timely cleaning or dumping of inhaled materials; 11. The machine is double-sealed and leak-proof ash design, with good sealing performance; 12. Lithium battery winding machine dust collector AJS series dust collector adopts 2.0 thick sheet metal, and has undergone a series of treatments such as laser cutting, bending, welding, grinding and polishing, spraying, high temperature baking paint, etc. The product does not peel off paint or rust; The work surface is smooth, easy to clean and impact resistant. Electronic control system 16 square meter cartridge filter Dust suppression louver Remote control wiring interface Programmable Pulse Controller External separate dust bucket Technical Specifications Unit YSL-150 YSL-220 Voltage V 380 380 Capacity L 30 30 Power KW 1.5 2.2 Air Flow M3/H 1200 1800 Noise Db 69 69 Vacuum Suction Kpa -1.3~-2.4 -1.3~-2.4 Filter Area m2 16 16 Filtering Accuracy Um 0.3 0.3 Qty of HEPA 个 2 2 Cleaning mode Pulse backflush Cable length M 8 8 Size(L*W*H) CM 87*73*185
MORE>
Applicable working conditions Laser engraving machine vacuum cleaner is suitable for automatic equipment, robot welding, laser engraving machine matching and other industries and production equipment. Product Overview The laser engraving machine vacuum cleaner YUSH T series is an industrial-grade special vacuum cleaner supporting automation equipment. The machine voltage is 380V, and the power of 4KW-7.5KW can be selected; the laser engraving machine vacuum cleaner can work continuously for 24 hours. Standard local/remote control switch function, which can be fixedly installed on large equipment as a fixed vacuuming device, and can be linked with the equipment. The total filtration area of the 6 filters of the laser engraving machine vacuum cleaner is 18M², the filtration accuracy is 0.3μm, and the programmable pulse cleaning design can set the automatic pulse cleaning interval of the machine according to the working conditions. Product Highlights 1. Laser engraving machine vacuum cleaner Three-phase electric 4KW/5.5KW/7.5KW industrial-grade vortex fan, can work continuously for 24 hours; there are phase loss, overheating and overload protection devices; 2. The machine has a split design and noise reduction treatment, the noise treatment effect is good, and the noise is low. 3. The laser engraving machine vacuum cleaner is equipped with 6 HEPA filters as standard, with a filter area of 18M², reducing the probability of filter blockage; 4. Programmable pulse cleaning system, the interval time of pulse cleaning filter can be set according to the working conditions to avoid the trouble of manual cleaning; 5. External large-capacity dust collector is convenient for dumping garbage; 6. The vacuum cleaner of the laser engraving machine is equipped with the remote/local switch function as standard, and the local switch or the linkage switch with the equipment can be selected according to the working conditions; 7. Cooling louver & cooling fan to improve the heat dissipation performance of the machine and reduce the load on the motor. 8. Movable universal wheel with brake, which is convenient for the machine to move. 9. The laser engraving machine vacuum cleaner machine occupies a small area, and the gray-white color is consistent with the color of most equipment on the market. 10. The machine body is made of thickened sheet metal, and has undergone a series of treatments such as laser cutting, bending, welding, grinding and polishing, spraying, and high-temperature baking paint. control panel Cooling louver/cooling fan Water separator 2 suction ports Pull-out dust bucket Remote control terminal Technical Specifications Unit YSL-400P YSL-500P YSL-700P power supply VAC 380VAC/50HZ rated power kw 4 5.5 7.5 Air flow m³/h 440 530 530 degree of vacuum Kpa -29 -30 -32 main filter area m2 18 18 18 Filtration accuracy um 0.3 0.3 0.3 noise db 70 74 76 Equipment suction diameter mm 40/50 40/50 40/50 barrel capacity L 15 15 15 Power cord length m 8 8 8 Air pressure Mpa 1Kpa≥work value≥0.4Kpa size mm 900*600*1450 cleaning method Pulse cleaning
MORE>
Applicable working conditions The central vacuum cleaner YSL is suitable for various processing places such as machinery manufacturing, metal processing, electronics, ceramics, chemicals, food, medicine, etc., and can be used with production lines or production equipment. Suitable for small central dust collection. YUSH YSL-185 is a three-phase electric, small central vacuum system with 18.5KW suction; 3-4 suction ports can be used at the same time, with constant pressure function, which can automatically control the air volume and suction of the machine's suction ports; filter system It consists of 6 filters with a total filter area of 28.8m². It has the function of pulse cleaning, and the interval time of pulse cleaning can be set; according to the needs of different working conditions, the "local/remote" switch can be selected; the external dust collector can be pulled out Trash can be dumped in the bucket. Features 1. The central vacuum cleaner has a constant pressure function, which can automatically control the air volume and suction force of the machine's suction port. The filtration accuracy of 2.0.3μm, the total filtration area is 28.8cm², and it is composed of 6 filters of 4.8 square meters, and the filter has an obvious effect of cleaning dust; 3. The "local/remote" switch can be selected according to the working conditions; 4. Central vacuum cleaner 50L external large-capacity dust collector is more convenient to clean up garbage; 5. 3-4 vacuum ports can work at the same time; 6. Built-in automatic pulse cleaning system, the pulse cleaning time interval can be set according to different working conditions, which can automatically clean the dust attached to the high-efficiency filter and prolong the service life of the filter; 7. The oil-water separator of the central vacuum cleaner can effectively filter the impurities in the compressed air and ensure the normal operation of the pulse system. 8. Thickened sheet metal is used, and has undergone a series of treatments such as laser cutting, bending, welding, grinding and polishing, spraying, high temperature baking paint, etc. The product does not peel off paint or rust; the work surface is smooth, easy to clean, and resistant to impact. Technical Specifications Unit Technical Parameters power supply vac 380VAC/50HZ rated power kw 18.5KW Air flow m³/h 1110 degree of vacuum mbar -340 main filter area m2 28.8 Filtration accuracy um 0.3 noise db 75 Equipment suction diameter mm 100 barrel capacity l 50 wire length m 8 weight kg 285 size cm 78*130*202
MORE>
Applicable working conditions Plasma laser cutting dust collector,YSL-1100B variable frequency constant pressure large air volume dust collector, is equipped with centrifugal fan, which has large air volume and low noise. The machine is equipped with Siemens inverter control system, which can automatically adjust the power of the motor, realize the variable speed operation of the motor, maintain a constant air volume and air pressure, and achieve the purpose of saving electricity. Plasma laser cutting dust collector programmable controller controls pulse cleaning method, 15 filters 100M² filter area, built-in air duct and other designs to ensure that the machine can be used stably for a long time in an environment with a large amount of dust without being blocked. The constant pressure control of the plasma laser cutting dust collector can monitor the negative pressure during use and remind to replace the filter; it is small in shape and low in noise, and is often used in laser cutting machines above 2.5*8 meters, plasma laser cutting machines, and robot welding workstations for equipment matching dust removal ; Product Description 1. The centrifugal fan of the plasma laser cutting dust collector has large air volume, low noise and stable performance; the cabinet modular design power, air volume, suction force, suction port and pipe diameter can be customized according to customer needs. 2. The Siemens inverter of the plasma laser cutting dust collector can automatically adjust the power of the motor, realize the variable speed operation of the motor, maintain a constant air volume and air pressure, and achieve the purpose of saving electricity; it can control the starting current of the motor, fully reduce the starting current, Reduce the maintenance cost of the motor. 3. Standard remote/local switch function, you can choose a local switch or a linkage switch with the equipment according to the working conditions. 4. The plasma laser cutting dust collector is equipped with a differential pressure gauge to measure the pressure when the machine is running. When the negative pressure exceeds the set value, it reminds to replace the filter. 5. External 60L pull-out dust collector. 6. 15 filters, the filter area is increased to 100M² to prolong the service life of the filter 7. The programmable pulse controller of the plasma laser cutting dust collector controls the pulse cleaning method, and the interval time of the automatic pulse cleaning filter can be set. 8. The installation method of the air inlet hose on the plasma laser cutting dust collector can avoid the wind loss caused by the narrow area. 9. The internal filtering wind speed reduction design of the plasma laser cutting dust collector machine can form dust reduction inside the machine after dust inhalation, reducing the dust adhesion to the filter. 10. The plasma laser cutting dust collector is small and has low noise and can be placed indoors or outdoors. Frequency conversion constant voltage control system Differential pressure gauge heavy duty door lock Separate dust bucket Duct chain interface Cartridge type high efficiency filter Technical Specifications Unit YSL-1100B power KW 11 Voltage 380V capacity L 60 Suction diameter MM 500 Filtration accuracy μm 0.1~0.3 number of filters EA 15 Filter size (diameter*height) mm 200*1100 total filter area M² 110 air flow volume M³/H 10000~13000 noise DB 74 vacuum suction Kpa -2.0~-3.0 Power cord length M 10 weight KG -- Air pressure 0.4Mpa≤work value≤0.6Mpa Size (L*W*H) MM 1400*1300*2500 Plasma laser cutting dust collector is mainly used for laser cutting machines above 2.5 meters, the collection and treatment of floating and suspended dust with a large amount of dust, and the small central dust collection system for multi-station operations; suitable for grinding, cutting, stirring, spraying Sand, ceramics, paper, steel, food, plastic, wood processing and other industries;
MORE>
Explosion-proof dust removal equipment is a kind of dust removal equipment suitable for explosion-proof conditions. The configurations are all configured to deal with flammable and explosive dust. Applicable working conditions Explosion-proof dust removal equipment is suitable for dust removal of metal, iron powder, aluminum powder, aluminum-iron alloy powder, silicon powder, zinc powder, titanium powder, titanium alloy powder, and ferrosilicon alloy powder. Product parameters Unit YSL-220E power kW 2.2 Voltage V - Hz 220/380 - 50/60 capacity l 30 total filter area m2 16 Filtration accuracy μm 0.3 number of filters PC 2 air flow volume m³/h 1800 Full pressure kPa 1.3-2.4 noise dB 68 Suction diameter mm 100/150 Power cord length m 8 Product Size mm 800*700*1850 Filter cleaning method —— Pulse cleaning
MORE>
